 Single Ninco lane changers |
|
|
|
|
 |
 |
  |
 21 Jul 2012, 16:29
Post
#16
|
|
|
Top Tuner  
Group: PLUS+ Posts: 364 Joined: 11-January 06 From: Bucks UK Member No.: 3,445  |
Yes but the lane changers don't work done both the straight cross over and the single lane changer above with a link to the dead strip not shown on picture ( right corner ) dip switches 1 off 2 on 3 on 4 on
but the lanes don't change --------------------  |
 |
|
|
21 Jul 2012, 18:43
Post
#17
|
|
|
Team Owner  Group: Members Posts: 1,065 Joined: 12-February 09 From: US Member No.: 11,432 |
Looking at the picture you just posted , your sensor seems to be UPSIDE DOWN. You want the black DOT to be towards the track surface. The Black dot is the sensor.
I almost more that mistake at fist. |
|
|
|
|
21 Jul 2012, 19:13
Post
#18
|
|
|
Trackhead Group: PLUS+ Posts: 711 Joined: 31-December 04 From: USA Member No.: 1,796 |
Maurizio mentioned at the SCI forum that the NINCO N-Digital - oXigen hybrid set up might not work since the oXigen car chip will lose power when going over the dead strip and not be able to initiate a lane change. You may be able to move the oXigen lane change chip slightly further away from the flipper to prevent this situation.
Best regards, Brian |
|
|
|
|
23 Jul 2012, 15:09
Post
#19
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
Hi.
On important thing: the coil wires are covered with enamel - that is, they are not conductive unless you remove with a blade the transparent coat. It is essential. Have you done that? Please check the part of the manual where this is explained. |
|
|
|
|
23 Jul 2012, 17:51
Post
#20
|
|
|
Top Tuner
Group: PLUS+ Posts: 364 Joined: 11-January 06 From: Bucks UK Member No.: 3,445 |
Yes I didnt cut and used the end that was originally soldered
-------------------- |
|
|
|
|
24 Jul 2012, 21:48
Post
#21
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
@nrwatson,
first thing to check is that there is power to the rail. Does a car run? Then, can you make sure the LC is powered? Can you aslo send us a lage picture, so I can check if there's something wrong in the wiring |
|
|
|
|
25 Jul 2012, 18:54
Post
#22
|
|
|
Top Tuner
Group: PLUS+ Posts: 364 Joined: 11-January 06 From: Bucks UK Member No.: 3,445 |
Power to track cars running fine with Oxigen
enclose a picture of the lane change double one 
crossover.jpg ( 442.29K )
Number of downloads: 35Thanks Maurizio -------------------- |
|
|
|
|
25 Jul 2012, 21:35
Post
#23
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
Neither of the LC work? Because if this is the case, then the problem lies elsewhere, it is very unlikely that both are failing.
How many cars have you got? |
|
|
|
|
26 Jul 2012, 05:32
Post
#24
|
|
|
Top Tuner
Group: PLUS+ Posts: 364 Joined: 11-January 06 From: Bucks UK Member No.: 3,445 |
I have two cars and two controllers at present power seems fine as work well on the track
I have the ninco analogue transformer and running the controllers with battery packs both original controllers with the bridge plug left in The dip switches are 1 off and the remaining three one Thanks neale -------------------- |
|
|
|
|
26 Jul 2012, 06:15
Post
#25
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
From your description and picture, dead strip seems to be properly soldered, and dip switches seem OK, in SSD compatible mode.
I understand both lane changer don't work, right? Email sent. |
|
|
|
|
26 Jul 2012, 17:31
Post
#26
|
|
|
Top Tuner
Group: PLUS+ Posts: 364 Joined: 11-January 06 From: Bucks UK Member No.: 3,445 |
yes and the other single straight doesnt work I am sure I am doing something stupid
-------------------- |
|
|
|
|
27 Jul 2012, 13:23
Post
#27
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
We need to find a way to check whether your cars are properly emitting the IR light. Do you have any SSD lane changers that you can try on?
|
|
|
|
|
27 Jul 2012, 13:57
Post
#28
|
|
|
Team Owner Group: Members Posts: 1,065 Joined: 12-February 09 From: US Member No.: 11,432 |
QUOTE (nrwatson @ 25 Jul 2012, 14:54)  Power to track cars running fine with Oxigen enclose a picture of the lane change double one
crossover.jpg ( 442.29K )
Number of downloads: 35Thanks Maurizio I keep saying this... the SENSORS ARE UPSIDE DOWN ! don't listen to me.. I dont know what Im talking about - heck I dont even own oxigen. 
|
|
|
|
|
27 Jul 2012, 15:36
Post
#29
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
I just checked...... you are right!!!!
I apologize, I didn't check well enough and didn't read all the posts well enough. Thanks. Neale, turn the sensor upside down. |
|
|
|
|
27 Jul 2012, 15:41
Post
#30
|
|
|
Team Owner Group: Members Posts: 1,243 Joined: 14-November 03 Member No.: 297 |
... there must be a reason if my wife says me that I'd miss the water in a river
 Actually I'm pretty sure she hides my stuff, then when I complain I can't find it, she puts it in my drawers where I had just looked, and says it was there from the beginning  |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 |
 |
| Lo-Fi Version | Time is now: 19th May 2013 - 16:44 |
Powered By IP.Board
© 2013 IPS, Inc.
Licensed to: SlotForum. All text, photos & graphics © 2003-2012 SlotForum or the member posting the content (unless indicated) - All rights reserved.
© SlotForum Copyright Notice - Please Read / © Aviso de copyright SlotForum - Léanlo, por favor / © A proposito del Copyright del contenuto di Slotforum - Per favore leggere attentamente