SlotForum banner
1 - 10 of 10 Posts

· Registered
251 Posts
Discussion Starter · #1 ·
Eligible Bodies
Carrera 997 RSR
Flyslot 997 RSR
Ninco 997 GT3 RS
Scalextric 997 GT3 Cup

Entrants name must be noted on underside of car as well as instructions for body float adjustments, if any.
Car numbers must be unique; no duplicate numbers chosen on a first come basis.

No changes to wheel wells allowed or altered body length or width from OEM. Please use your discretion, the objective is that the car looks like a scale race car from the period. Cars should represent the actual race car, and not appear slammed our have wheels and tyres that appear to be out of scale. Cars can be lowered, but must maintain a natural stance.

-----Tires must fit fully under the fenders. Tires may NOT project beyond body work when viewed from above.
-----Bodies must be removable to allow inspection and photography after the last race, and if needed to allow maintenance and repair during the race series.

Weight there is no weight limit or minimum. All weight must be placed inside (covered by the body) and there can be no weight placed on the bottom of the chassis or outside of the body, or any other place including the guide. NO weighted guides.

Lightweight interiors allowed, but must be 3 dimensional and painted to show drivers head, shoulders, arms, steering wheel and dash. Drivetrain and wires are to be covered by the interior when peering through windows and the driver should also be clearly visible.

-----Clear window material must be present; whether a windshield or a windscreen and may be vacuum formed or plastic only.

ANY chassis that is stock, aftermarket, scratch built, or 3D printed using any material, is eligible. Podded or non-podded chassis allowed
-----Inline / sidewinder / anglewinder configurations all OK
-----Underside of car chassis and body must clear track road surface, on level track, by 1.0mm minimum the gear may be lower so long as it does not interfere with the track surface.
-----Guide must be entirely under body, and NOT visible when viewed from above.
-----Traction magnets are NOT permitted.
-----Suspension permitted
-----Axle bushing and bearings are allowed on front and rear.
-----All chassis MUST be mounted like an RTR car - meaning screws through the chassis to body mounting points and no pins THROUGH the body, Velcro, etc. However, a chassis with side mounts such as the HRS/HSR-2 can be used - as long as the pins do NOT go through the body. (we may also revisit this one)

ANY stock or aftermarket gears and ratios of your choice may be used.

ANY commercially available FC-130, FK-130, FK-180 (including Flat 6 models) or FF-050 motor with a RPM limit of 22000. Motors cans are not to be opened or modified. Wrapper can be removed for clearance.

plastic, magnesium or aluminum wheels are allowed. Wheels must have period inserts or look reasonably period for the car - no blank aluminum insert wheels please.
Minimum diameter 15.8 mm
Minimum width 7mm front
Maximum width 12mm Rear

Only BLACK RUBBER tires are allowed with a minimum OD of 19mm for rear tires with a maximum width of 12mm at the start of the series. Minimum front tire diameter will be 17mm; minimum width of 7mm. All tires must be black.
Tires may be cleaned in any manner prior to shipping them to the first race, but may not be prepared by oil-soaking or other chemical means. Nail polish or clear coating of front tires is allowed. TIRES CAN BE CLEANED BY the host prior to qualifying or if deemed detrimental to the performance of competitors cars.

If a car is damaged during a race, or has a mechanical issue, the owner will have the option to have the car returned at his cost, or have the track host repair the car. The impact (if any) to the results from that race will be the only penalty. Shipping expenses must be paid for by the owner, and the series will continue at the scheduled pace. Cars that are returned to the owner during the event, can only have the needed repair work done, and must be returned to the series without additional tuning or refreshing. Consideration and fairness will be employed, especially when a car is damaged during the series due to no-fault of the entrant.
If a car(s) is significantly damaged during shipping, all effort will be made to repair the car(s) to its original state where possible the race event will be delayed to facilitate the repairs
There is no allowance made for a car to be tuned, or have parts replaced for improved performance during a series.
Cars that do not meet these rules and/or could impede the performance of other cars during the series will have a 2 point penalty applied. Multiple infractions will incur multiple penalty points up to a maximum of 12 points. Cars that are deemed to be unsafe and/or could impede the performance of other cars will not be allowed to race and will be returned and/or made compatible.
Decisions by the Race Director are final, the onus is on the builder to ensure his/her car meets the rules and are compatible to the track and fellow entrants. The Race Director reserves the right to exclude or penalize an entry at his discretion for anything else arising that is not specifically mentioned in the rules.

Are lined up across the USA and Canada. I will list them soon. Keep in mind tracks may be subject to change due to restrictions and social distancing requirements as safety is first over our toy car competition. All tracks are to be run between 10-12 volts and at the discretion of the host.

Participants are limited to 24 entries.
Track hosts have agreed this is a manageable number in the event of solo or social distance racing

ENTRY FEE 26.00 USD Due June 1st
Due Date : June 30th 2021

Sponsors and prizes will be listed soon will be a great place to shop for motors gears and additional wheels and tires that fit your builds.
NSR will support our proxy directly as well with a few prizes
Im waiting to hear back from a few others.

· Registered
251 Posts
Discussion Starter · #4 ·
Registration List of Builders, we may move to a field of 27 and a Shootout format to determine the grid.

December 24, 2020, 09:06 AM
1) #20 BARC 1
2) #5 Redlynr
3) #33 Brumos RSR NSR 997
4) #12 Fast Co.
5)#54 Manchvegasracer
6) #2 CourtneyS
7) #9 REL13
8) #111 Peter Gunn
9) #96 ALS
10) #44 Gascarnut
11) #1 Audi 1
12) #76 Cj74
13) #57 SteeveeW
14) #7 Dungeonracer
15) # tbd Lou E
16) # 59 Austin
17) # 53 ArroldN
18) #6 Aloha
19) # 4 Big Duhg
20) #71 Leadfinger
21)#tbd Pepsi62
22) #86 just Dave Scalextric Porsche 997 Cup
23) #10 CgyRacer
24) #64 Authur64


1) Apexbomber
3) Doubl-B
5) SirChrisGuyW
6) Lance
7) Lez

· Registered
1,873 Posts
Well the proxy has finished and i finished 19 out of 29 not bad for a first attempt over there , car could have finished higher as it was very close between a number of us so positive of improving next time it,s run.
The car came home with not a scratch on it , tyres could have run a few more rounds , braids were still in good conditiion , so what did i learn well i can still make good handling cars but need more speed , the series runs 21.5k motors i used a Thunderslot in sidewinder form , next time out after testing here with a Pirana motor hope that will be enough to be competative , thanks to all the people who put this on great series., and i got some goodies included in the return box

Table Hood Vehicle Car Toy
1 - 10 of 10 Posts